Firewood is used to provide fire which in turn warms the immediate surroundings. This method has been used since earlier times to protect the people from the cold weather especially during the winter season. More than a couple of decades ago, gas log installation South Lake TX, have introduced the concept of producing fire in furnaces without the use of actual wood.
A gas log is an artificial wood that is actually a burner. Its fire is supplied with natural gasses or propane. It can be ceramic or cement. It exists in two types, vented and ventless. Vented types burn with the dampers open or semi open. Ventless ones operate with the dampers close. Both should be installed in a wood burning furnace.
Before installation, it is very necessary to know if you have volatile substance or wood burning fireplaces. This should be on top of your list because ironically, ceramic and cement logs cannot be installed on a gas burning furnace. Installing artificial logs on a furnace like this increases the risk of asphyxiation due to increased production of smoke. It can also likely burn the building down.
A masonry fireplace is suitable for both vented and ventless types. Tilt up versions of this type of fireplace that are made of bricks or concrete have good compatibility level. Dampers which can be opened and can be closed are best in installing these man made woods. Never install them on a gas stove.
There are simple and general steps in installing artificial firewood. You have to make the burner pan ready first by connecting the safety valve nearest to it after making sure that the fireplace adjustment knob is not turned on. Secure the connection by tightening it.
Then, attach the supply line into the effluvium outlet. You can do this by using two wrenches, one to hold the outlet steady and the other to remove the cap. Follow with connecting the supply line to the outlet. You can test for leaks by spraying soapy water on the part where the ports meets. If bubbling occurs, turn off the the effluvium outlet. Refit the lines and check again.
What follows is attaching the parts. Connect the main assembly and diverter bracket to the pan. A heat shield should cover the heat valve to prevent it from overheating. Afterward, install the sand, rocks and logs.
Evenly distribute sand over the pan. This action action makes the fire consistent. Be sure not to cover the pilot light when distributing. Rock wool and vermiculite will be put over the sand. Lava rocks should then be poured over the entire fireplace. Place the grate on top of the pan. Stack ceramic logs according to the manufacturer manual. Every parts mentioned are found in the product package.
The gas log installation South Lake TX is an instant and efficient way in providing you with a cozy warmth. You do not have to clean up the ashes from fireplaces and it produces fewer emissions than ordinary firewood. However, it does not mean that you should already purchase them without careful consideration. Some people still choose the pleasant aroma of naturally burning firewood.
A gas log is an artificial wood that is actually a burner. Its fire is supplied with natural gasses or propane. It can be ceramic or cement. It exists in two types, vented and ventless. Vented types burn with the dampers open or semi open. Ventless ones operate with the dampers close. Both should be installed in a wood burning furnace.
Before installation, it is very necessary to know if you have volatile substance or wood burning fireplaces. This should be on top of your list because ironically, ceramic and cement logs cannot be installed on a gas burning furnace. Installing artificial logs on a furnace like this increases the risk of asphyxiation due to increased production of smoke. It can also likely burn the building down.
A masonry fireplace is suitable for both vented and ventless types. Tilt up versions of this type of fireplace that are made of bricks or concrete have good compatibility level. Dampers which can be opened and can be closed are best in installing these man made woods. Never install them on a gas stove.
There are simple and general steps in installing artificial firewood. You have to make the burner pan ready first by connecting the safety valve nearest to it after making sure that the fireplace adjustment knob is not turned on. Secure the connection by tightening it.
Then, attach the supply line into the effluvium outlet. You can do this by using two wrenches, one to hold the outlet steady and the other to remove the cap. Follow with connecting the supply line to the outlet. You can test for leaks by spraying soapy water on the part where the ports meets. If bubbling occurs, turn off the the effluvium outlet. Refit the lines and check again.
What follows is attaching the parts. Connect the main assembly and diverter bracket to the pan. A heat shield should cover the heat valve to prevent it from overheating. Afterward, install the sand, rocks and logs.
Evenly distribute sand over the pan. This action action makes the fire consistent. Be sure not to cover the pilot light when distributing. Rock wool and vermiculite will be put over the sand. Lava rocks should then be poured over the entire fireplace. Place the grate on top of the pan. Stack ceramic logs according to the manufacturer manual. Every parts mentioned are found in the product package.
The gas log installation South Lake TX is an instant and efficient way in providing you with a cozy warmth. You do not have to clean up the ashes from fireplaces and it produces fewer emissions than ordinary firewood. However, it does not mean that you should already purchase them without careful consideration. Some people still choose the pleasant aroma of naturally burning firewood.
About the Author:
Read more about Quick And Simple Steps In Gas Log Installation visiting our website.
No comments:
Post a Comment